Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
Page 37
Page 38
Page 39
Page 40
Page 41
Page 42
Page 43
Page 44
Page 45
Page 46
Page 47
Page 48
Page 49
Page 50
Page 51
Page 52
Page 53
Page 54
Page 55
Page 56
Page 57
Page 58
Page 59
Page 60
Page 61
Page 62
Page 63
Page 64
Page 65
Page 66
Page 67
Page 68
Page 69
Page 70
Page 71
Page 72
Page 73
Page 74
Page 75
Page 76
Page 77
Page 78
Page 79
Page 80
Page 81
Page 82
Page 83
Page 84
Page 85
Page 86
Page 87
Page 88
Page 89
Page 90
Page 91
Page 92
Page 93
Page 94
Page 95
Page 96
Page 97
Page 98
Page 99
Page 100
Page 101
Page 102
Page 103
Page 104
Page 105
Page 106
Page 107
Page 108
Page 109
Page 110
Page 111
Page 112
Page 113
Page 114
Page 115
Page 116
Page 117
Page 118
Page 119
Page 120
Page 121
Page 122
Page 123
Page 124
Page 125
Page 126
Page 127
Page 128
Page 129
Page 130
Page 131
Page 132
Page 133
Page 134
Page 135
Page 136
Page 137
Page 138
Page 139
Page 140
Page 141
Page 142
Page 143
Page 144
Page 145
Page 146
Page 147
Page 148
Page 149
Page 150
Page 151
Page 152
Page 153
Page 154
Page 155
Page 156
Page 157
Page 158
Page 159
Page 160
Page 161
Page 162
Page 163
Page 164
149775.829.7272 standoffsystems.com HOW TO INSTALL EDGE GRIPS CLIPS nylon anchor barrel gripper nylon tip set screw set screw TIP1Formaterialover12thicktemporarilyremovenylontipsetscrewstomakedimpledmarks. TIP 2 Align the barrels so the flat side of the gripper will line up with the barrels set screw hole. NOTE There is a tip on the base of the gripper to dimple the mounting location on softer surfaces such as drywall and wood. For masonry use a piece of masking tape as a pad to receive the mark. Mount the grippers to your panel by placing the grippers on the edges and tightening the nylon tips against back of the panel. Hold the panel and grippers level against the wall and press to create dimpled marks on your mounting surface. Pre-drill 14 holes in your surface then insert nylon anchors into the holes and tap them flush. Mount barrels to wall with the washer head screws then insert the grippers and tighten set screws. 1 2 3 4 washer head screw 14 hole not required for wood pre-drill 18 hole instead nylon anchor vinyl shims disc clip oval head screw not required for wood pre-drill 18 hole instead TIP Panel clips should be installed at the top and bottom and at least 23 in from the sides of glass mirrors plastic materials not critical. NOTE Vinyl shims are used to accommodate different material thicknesses. Mark the wall 316 above and below your desired location of the panel edges. Pre-drill 14 holes in your surface then insert nylon anchors into the holes and tap them flush. Drive oval head screws into anchor to mount lower clips. Slide in panel and install upper clips. Remove the adhesive backing from discs and place one into the recess on the face of each clip. 1 2 3 4 14 hole HOW TO INSTALL standoff edge grips HOW TO INSTALL standoff panel clips Visit standoffsystems.comhowto to browse our collection of how-to videos.